New Projects

I have been busy working on a few new projects even though I have yet to completely finish the old ones. Been feeling a bit under the weather this week as well so that has put a damper on the ambitions.

Last week Ashley came home with this old desk that she picked up from one of her Facebook Mom’s sites. She got it for $5!  The intent is to put this in our bedroom for her to use as a hair and makeup vanity.  It does need some work though. The veneer is peeling off of the top and sides and the middle drawer is pretty much busted.  The remaining drawers will all fall out if pulled too far.

But I love a challenge and I have already started to rebuild it. I am going to put a new plywood top on with edging around the sides of it. It will be stained a nice dark color.  The rest of the desk will be painted and antiqued in a white finish with fresh new hardware.

Another project I have started is a art room table for my sister-in-law. Its going to be one of those fancy ones using a 6-cube shelf from Home Depot topped off with an old door from the Habitat Restore.  So far I have picked up the doors, assembled the shelf, and cut some peg board for the back of it. I am hoping this weekend will allow some more time to get the door cut to size and some trim wrapped around it and the shelf.

The last thing I have going on is an update to the new swing set. It was always our intent to put a sandbox underneath it but before doing that, I wanted to raise the sides up a bit, fashion a cover to keep animals out, and put a chalkboard under there. I have the new boards for the sides cut and ready to go and I found an old piece of plywood to use for the chalkboard. I even have some old trim that I am going to use to frame it out.

The last thing it needs is a cover that can be easily removed. I do have the wood from the old sandbox box that was built and never used but its a bit heavy. A reinforced plywood top would really be better for this. I will have to see what I have around the shop. 🙂

New Swing Set

It took a bit longer than I expected but I finally got the swing set put together. This thing is sturdy and build to last! I am so glad we went with a build it yourself model from the local lumber-yard vs a kit from one of the big box stores. We wanted one that could support everyone from our 10 month old all the way up to me. 🙂

Overall it took one full day of cutting and assembling and then a few hours here and there after work to put the finishing touches on it.

More Column Work and Swing Set Wood

We had a super busy weekend. Along with Mother’s Day, we spent most of Saturday cutting, mitering, and nailing up some more trim pieces on the kitchen pass through project. More on that later.

And if we didn’t have enough projects going on, we finally settled on a swing set for the kids. Not just any swingset though. A real one that is going to require cutting before it can be assembled! No shortcuts here!

Ashley also spent a good part of her special day beautifying our front and back yards with this years flower selection.

A great weekend and we are looking forward to what the week will bring us.

Kitchen Pass Through Project – Part II

We are making some good progress on the kitchen pass through project. Phase II is complete and we are now ready to begin the corner moldings. But first, here is a brief recap on how we got to where we are.

After removing the trim along the inside of the pass through along with the floor trim, we screwed 2×2’s onto each side of the wall. We wanted to make each column as close to a square as possible. Adding the 2×2’s got us quite a bit closer.

With the 2×2’s in place, we then moved onto the MDF. I purchased 3 sheets of 1/2″ 4’x8′ MDF from Home Depot and had the fine folks there rip them down to 2’x8’s sheets for ease of transport.

Cutting them at home was made much easier with my new Kreg Rip-Cut tool.  If you do a lot of long cuts, this tool is a must have.  What a life saver and so easy to use!

Anyway, we cut the MDF to size and hammered them to the 2×2’s using simple nails. Not perfectly square or pretty but since this is only the 1st layer, I am thinking it shouldn’t matter to much.  At least I am hoping it doesn’t matter to much. 🙂

It is looking so much better already!  The gap near the top of each column was supposed to be where a piece of trim would slide in but I screwed up the measurements and it should have been an inch lower.

I will have to cover it up and then think of something else. Oh well. It happens. 🙂

Kitchen Pass Through Project – Part I

When we moved into our house over 2 years ago, we knew that at some point we wanted to remove the half wall that separated our living room from our dining room.

The problem was, we were pretty sure that its a load bearing wall and we really didn’t want to find out the hard way. So for two years it has sat there looking like it does. Being used as a bench, a road for hot wheels, and a shelf for storage. 
Now the time has come to finally do something with it. After searching through our favorite project site (Pinterest) we decided to move our Island into the space occupied by the wall, add a bench and new table, and have a new seating area!
Here is our inspiration for the space. 
http://www.decorpad.com/designers/Oxford-Development
We started out by tearing off the drywall. This to me was the scariest part because you never really know what you are dealing with until the drywall comes off. 
Case in point, I was assuming the electrical cable was going to be running along the wall and could then easily move the outlet into the island. But nope! It was run up through the floor. 🙁
I also managed to flip the breaker when knocking the sheetrock off. Apparently the sheetrock loosened the outlet and allowed it to come undone. That caused a short in the line and the breaker to flip. Oops!

In order to the the wire over to the far side of the island, I proceeded to drill some small holes near the wall and got the electrical wire to come up through that.

We also removed the carpet and laminate flooring where the island would eventually sit.

After some dry fitting, we moved the island into its permanent home and ran the electrical line up into it.  The guy at Lowes that helped me find the fittings I needed thought I was crazy going with the setup that I wanted. But with four kids, I always prefer to overdue the safety a bit to ensure that everyone is not exposed to anything that they should not be.

I had just enough wire to get to the outlet and even had to flip it upside down in order to make it work. But work it does!

For some ideas on space, we proceeded to move our dining room table and bench into the kitchen and it has stayed there since. We already love the functionality that this has brought into our home.  For the longest time, if we wanted to eat in the kitchen, we had to do it at the island which in turn would only seat 2 people. The rest would have to stand. And even though the dining room is close enough, sometimes you just dont feel like making the move to such a formal space. 
The pics below depict the island in its new home (without the top).  Part II will showcase the building out of the side columns. Now things are going to get exciting!